Skip to main content
Workforce LibreTexts

5.5: Full-wave Center-tap Rectifier

  • Page ID
    1268
  • \( \newcommand{\vecs}[1]{\overset { \scriptstyle \rightharpoonup} {\mathbf{#1}} } \) \( \newcommand{\vecd}[1]{\overset{-\!-\!\rightharpoonup}{\vphantom{a}\smash {#1}}} \)\(\newcommand{\id}{\mathrm{id}}\) \( \newcommand{\Span}{\mathrm{span}}\) \( \newcommand{\kernel}{\mathrm{null}\,}\) \( \newcommand{\range}{\mathrm{range}\,}\) \( \newcommand{\RealPart}{\mathrm{Re}}\) \( \newcommand{\ImaginaryPart}{\mathrm{Im}}\) \( \newcommand{\Argument}{\mathrm{Arg}}\) \( \newcommand{\norm}[1]{\| #1 \|}\) \( \newcommand{\inner}[2]{\langle #1, #2 \rangle}\) \( \newcommand{\Span}{\mathrm{span}}\) \(\newcommand{\id}{\mathrm{id}}\) \( \newcommand{\Span}{\mathrm{span}}\) \( \newcommand{\kernel}{\mathrm{null}\,}\) \( \newcommand{\range}{\mathrm{range}\,}\) \( \newcommand{\RealPart}{\mathrm{Re}}\) \( \newcommand{\ImaginaryPart}{\mathrm{Im}}\) \( \newcommand{\Argument}{\mathrm{Arg}}\) \( \newcommand{\norm}[1]{\| #1 \|}\) \( \newcommand{\inner}[2]{\langle #1, #2 \rangle}\) \( \newcommand{\Span}{\mathrm{span}}\)\(\newcommand{\AA}{\unicode[.8,0]{x212B}}\)

    PARTS AND MATERIALS

    • Low-voltage AC power supply (6-volt output)
    • Two 1N4001 rectifying diodes (Radio Shack catalog # 276-1101)
    • Small “hobby” motor, permanent-magnet type (Radio Shack catalog # 273-223 or equivalent)
    • Audio detector with headphones
    • 0.1 µF capacitor
    • One toggle switch, SPST (“Single-Pole, Single-Throw”)

    It is essential for this experiment that the low-voltage AC power supply is equipped with a center tap. A transformer with a non-tapped secondary winding simply will not work for this circuit.

    The diodes need not be exact model 1N4001 units. Any of the “1N400X” series of rectifying diodes are suitable for the task, and they are quite easy to obtain.

    CROSS-REFERENCES

    Lessons In Electric Circuits, Volume 3, chapter 3: “Diodes and Rectifiers”

    LEARNING OBJECTIVES

    • Design of a center-tap rectifier circuit
    • Measuring “ripple” voltage with a voltmeter

    SCHEMATIC DIAGRAM


    05138.webp

    ILLUSTRATION


    05139.webp

    INSTRUCTIONS

    This rectifier circuit is called full-wave because it makes use of the entire waveform, both positive and negative half-cycles, of the AC source voltage in powering the DC load. As a result, there is less “ripple” voltage seen at the load. The RMS (Root-Mean-Square) value of the rectifier’s output is also greater for this circuit than for the half-wave rectifier.

    Use a voltmeter to measure both the DC and AC voltage delivered to the motor. You should notice the advantages of the full-wave rectifier immediately by the greater DC and lower AC indications as compared to the last experiment.

    An experimental advantage of this circuit is the ease of which it may be “de-converted” to a half-wave rectifier: simply disconnect the short jumper wire connecting the two diodes’ cathode ends together on the terminal strip. Better yet, for a quick comparison between half and full-wave rectification, you may add a switch in the circuit to open and close this connection at will:


    05141 (1).png


    05140.png

    With the ability to quickly switch between half- and full-wave rectification, you may easily perform qualitative comparisons between the two different operating modes. Use the audio signal detector to “listen” to the ripple voltage present between the motor terminals for half-wave and full-wave rectification modes, noting both the intensity and the quality of the tone. Remember to use a coupling capacitor in series with the detector so that it only receives the AC “ripple” voltage and not DC voltage:


    05142.png

    COMPUTER SIMULATION

    Schematic with SPICE node numbers:

    05143.png

    Netlist (make a text file containing the following text, verbatim):

    b.PNG


    This page titled 5.5: Full-wave Center-tap Rectifier is shared under a GNU Free Documentation License 1.3 license and was authored, remixed, and/or curated by Tony R. Kuphaldt (All About Circuits) via source content that was edited to the style and standards of the LibreTexts platform; a detailed edit history is available upon request.

    • Was this article helpful?